MANLEY SNAPPER

Usato, in ottime condizioni, privi di segni di usura evidenti. Dotati di imballo originale.

Coppia di finali di potenza monofonici

Specifiche tecniche

Input Impedance RCA: 475 Kohm
Input Impedance XLR: 15 Kohm or 600 Ohm switchable
Input Sensitivity RCA: 750mV input = 110W output
Input Sensitivity XLR @ 15Kohms: 1.5 V input = 110W output
Input Sensitivity XLR @ 600 Ohms: 2.4 V input = 110W output (w/600 Ohm source)
Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB
Gain XLR: factory set for 25 dB
Negative Feedback: factory set for 9dB of global NFB
Maximum Output Power into 5 Ohms: 110 Watts (1.5% THD @ 1kHz)
Maximum Output Power into 8 Ohms: 100 Watts (1.5% THD @ 1kHz)
Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K
Noise Floor: Typically 105?V = -77dBu A-WGT Typically 388?V = -66dBu unweighted
Dynamic Range: 98dB
THD+noise @ 1W: less than 0.1%
Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT
Frequency Response at 5W into 5 Ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz
Recommended Speaker Load: Optimized for 5 Ohms
Actual Output Impedance: 1.5 Ohms
Power Consumption (idle): 170 Watts (1.4A @120VAC)
Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)
Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency: 50~ 60Hz
Tube Complement (per each chassis):
Input Vacuum Tube: 1 x 12AX7 (front 9-pin tube)
Driver Vacuum Tube: 1x JAN NOS GE 7044 or 5687 (equivalent) (middle 9-pin tube)
Output Vacuum Tubes: 4 x Tungsol EL34B
B+ Voltage: 570V DC
Output Tube Quiescent Standing Current: 30mA
Set Bias for: 300mVDC measured across 10 Ohm cathode resistor
Lamp type: "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs
Fuse values & types for SN#MSNP848 and below:
120VAC operation: MDL or MDA 4A / 250 Volt SLO-BLO size 1/4" X 1 1/4"
240VAC operation: MDL or MDA 2A / 250 Volt SLO-BLO size 1/4" X 1 1/4"
Fuse values & types for SN#MSNP849 and above:
120VAC = 5A/250V SLO-BLO, 5 x 20mm
240VAC = 3.15A/250V SLO-BLO, 5 x 20mm
B+ FUSE: MDA 1/2A Ceramic SLO-BLO size 1/4" x 1 1/4"
Dimensions: 15" deep x 13" wide x 8.75" tall
Shipping weight each: 45 pounds